Product Details
Advanced Detergent Technology Removes Harmful Deposits
The potent detergent-based formula in AMSOIL Engine and Transmission Flush targets the root cause of performance degradation in engines and transmissions. Over time, stop-and-go driving, prolonged idling, short trips that prevent engines from reaching full operating temperature, towing, airborne dirt ingestion, fuel dilution, water condensation, and oxidized oil contribute to sludge formation. This sludge settles in critical areas, clogging narrow oil passages and restricting vital lubricant flow to components like the upper valve train area.
The advanced formulation combines light base oil technology with powerful detergents and dispersants to provide safe yet effective cleaning action. These sophisticated cleaning agents work together to dissolve varnish, break down carbon deposits, and disperse accumulated contaminants throughout the system. The detergent chemistry is specifically engineered to maintain compatibility with both petroleum-based and synthetic lubricants, ensuring safe operation regardless of the existing oil type.
Unlike harsh solvent-based cleaners that can damage seals and gaskets, this detergent-based approach provides thorough cleaning while maintaining complete compatibility with engine and transmission components. The formulation includes carefully balanced surfactants that lift deposits from metal surfaces without causing swelling or deterioration of rubber seals, O-rings, or gasket materials commonly found in modern powertrains.
Restores Engine Performance and Efficiency
Sludge accumulation in engines creates multiple performance problems that compound over time. When deposits settle in narrow oil passages, lubricant flow becomes restricted, leading to inadequate lubrication of critical components. This restriction particularly affects the upper valve train area, where precise oil delivery is essential for proper valve operation, hydraulic lifter function, and timing chain or belt tensioner operation.
AMSOIL Engine and Transmission Flush addresses these issues by helping to loosen sticky valves and piston rings, which minimizes blow-by gases and reduces harmful emissions. The cleaning action removes deposits from oil control rings, allowing them to maintain proper cylinder sealing and reducing oil consumption. Clean valve stems and guides enable proper valve seating, improving compression and combustion efficiency.
The restoration of proper oil circulation promotes lower operating temperatures throughout the engine. When oil passages are clear and unrestricted, the lubricant can effectively carry heat away from critical components like pistons, bearings, and cylinder heads. This improved heat transfer capability helps prevent hot spots that can lead to accelerated wear, oil oxidation, and component failure.
Engine noise reduction is another significant benefit achieved through deposit removal. Hydraulic valve lifters operate more quietly when supplied with clean, unrestricted oil flow. The cleaning action removes varnish and deposits that can cause lifter pump-up or collapse, eliminating the characteristic ticking or tapping noises associated with contaminated valve train components.
Transmission Cleaning for Smooth Operation
Automatic transmissions face unique challenges from deposit formation that can severely impact shift quality and component longevity. Transmission fluid operates under extreme conditions, including high temperatures, pressure cycling, and constant agitation through torque converter action. These conditions promote oxidation and deposit formation on critical components like clutch plates, valve bodies, and oil cooler passages.
Deposits on clutch plates create particularly problematic conditions within automatic transmissions. When friction material surfaces become glazed or contaminated with varnish, the clutch packs cannot properly engage or disengage. This condition leads to hesitation during shifts, erratic shift timing, and increased slippage that generates additional heat. Over time, clutch glazing reduces the effective life of the transmission and can necessitate costly rebuilds or replacements.
The cleaning action of AMSOIL Engine and Transmission Flush removes these deposits and varnish from clutch plates, helping restore proper friction characteristics and improving shift efficiency. Clean clutch surfaces provide consistent engagement, reducing shift delays and eliminating harsh or erratic shifting patterns. The improved friction characteristics also reduce heat generation during normal operation, extending component life.
Oil cooler and port cleaning represents another critical benefit for transmission longevity. Modern automatic transmissions rely on efficient heat dissipation through oil coolers and carefully designed fluid passages. When these areas become restricted with deposits, transmission operating temperatures increase, accelerating fluid breakdown and component wear. The cleaning action unclogs these vital passages, restoring proper heat transfer and extending transmission life.
Usage Instructions and Applications
AMSOIL Engine and Transmission Flush is recommended for use in gasoline and diesel engines, as well as automatic transmissions. The product should not be used in differentials, as these components require different cleaning approaches and fluid characteristics. The formulation is compatible with both conventional and synthetic lubricants, making it suitable for vehicles with various maintenance histories.
For engine applications, add the entire contents of one 16-ounce bottle to the engine oil fill port while the engine is warm but not hot. Allow the engine to idle for 10 to 15 minutes to circulate the cleaning solution throughout the system. This idle period enables the detergents to dissolve deposits and the dispersants to suspend contaminants in the oil. Immediately after the idle period, drain the oil completely and ensure adequate time for thorough drainage. Replace the oil filter before refilling with fresh engine oil in the viscosity grade specified by the vehicle manufacturer.
Transmission cleaning requires a slightly modified procedure to account for the complexity of automatic transmission systems. With the vehicle on level ground and the emergency brake engaged, add the entire bottle to the transmission oil fill port. Idle the engine for 10 to 15 minutes, then shift through all gear positions including drive and reverse to circulate the cleaning solution through all hydraulic circuits. Avoid placing the vehicle under heavy load during this process to prevent potential damage to cleaned but not yet replaced fluid systems.
Complete transmission and torque converter drainage is essential after the cleaning cycle. The transmission filter must be changed before refilling with fresh transmission fluid, as the old filter will contain suspended contaminants removed during the cleaning process. This procedure is not recommended for transmissions without removable pans or accessible filters, as proper filter replacement is crucial for optimal results.
Environmental Safety and Disposal
The detergent-based formulation of AMSOIL Engine and Transmission Flush offers significant environmental advantages over solvent-based cleaning products. The used cleaning solution can be disposed of with waste oil through standard recycling channels, eliminating the need for special hazardous waste handling procedures. This compatibility with existing waste oil disposal systems reduces environmental impact and simplifies the cleaning process for both professional and consumer users.
The cleaning effectiveness achieved in a single treatment reduces the need for multiple cleaning cycles or aggressive chemical interventions. This one-treatment approach minimizes the total volume of cleaning chemicals required and reduces the environmental footprint of maintenance operations. The compatibility with seals and gaskets also prevents the premature replacement of these components, further reducing waste generation.
Technical Documentation and Resources
Comprehensive technical information and installation guidance are available through detailed product documentation. These resources provide specific application instructions, compatibility information, and troubleshooting guidance for various vehicle types and maintenance scenarios.
- Technical Data Sheet (PDF) - Complete product specifications, performance characteristics, and detailed application instructions
- Product Data Bulletin (PDF) - Application guidelines, compatibility information, and frequently asked questions
- Warranty Information (PDF) - Product warranty terms and coverage details
- VIN Code Lookup (PDF) - Vehicle identification and specification matching guide
Frequently Asked Questions
Engine flush cleans the entire lubrication system including oil passages, valve train components, and crankcase areas, while fuel injector cleaner specifically targets the fuel delivery system. Engine flush removes oil-based deposits and sludge through the lubrication system, whereas fuel injector cleaner addresses carbon deposits and fuel varnish in injectors, intake valves, and combustion chambers.
High-mileage vehicles typically benefit significantly from flush treatments due to accumulated deposits from extended service intervals. The cleaning action helps restore proper oil circulation, reduces consumption, and can improve performance in engines and transmissions with deposit-related issues. However, vehicles with severely neglected maintenance may require professional evaluation before flush treatment.
The product is safe for use at every oil change, though most applications require treatment only when deposit accumulation is evident through symptoms like increased oil consumption, noisy operation, or poor shift quality. Vehicles with regular maintenance typically need flush treatment every 30,000 to 50,000 miles, while neglected systems may benefit from more frequent applications initially.
AMSOIL Engine and Transmission Flush is fully compatible with both synthetic and conventional petroleum-based lubricants. The detergent-based formula will not react adversely with any lubricant type, making it suitable for vehicles transitioning between oil types or with unknown maintenance histories.
Engine and transmission flush cleans the lubrication system through the oil, while diesel fuel additives treat the fuel system including injectors, fuel pumps, and combustion chambers. These products address different contamination sources and serve complementary functions in comprehensive vehicle maintenance programs.
The detergent-based formulation is specifically designed to be compatible with seals and gaskets of all ages and materials. Unlike harsh solvent-based cleaners, this product will not cause swelling, shrinkage, or deterioration of rubber components commonly found in engines and transmissions.
Gasoline stabilizer prevents fuel degradation during storage and provides minimal cleaning action in the fuel system, while engine and transmission flush provides intensive cleaning of the lubrication system. These products serve entirely different purposes and are not interchangeable for cleaning applications.
This product works exclusively through the lubrication system and does not provide octane boost or direct fuel system cleaning benefits. For fuel system maintenance, separate fuel additives specifically designed for injector cleaning, octane enhancement, or fuel stabilization should be used in conjunction with lubrication system cleaning.
The detergent-based formulation allows for disposal with regular waste oil through standard recycling channels. This environmental advantage eliminates the need for special hazardous waste handling procedures required by many solvent-based cleaning products.